Adjusted via switches S0–S3. For example, setting S1, S2, and S3 to "ON" with S0 "OFF" configures the driver for 1000 steps per turn.
Controlled via switches I1 and I2 to manage torque and heat generation (e.g., 10A current is set with I1 ON and I2 OFF).
Entrada do trem de pulso que dita a velocidade e quantidade de passos do motor.
Ensure all wiring is correct before applying power. The driver will initialize. hb-b3hl manual pdf %C3%B3leo
While the HB-B3HL driver controls the electrical pulses, it moves heavy mechanical components like ball screws, linear guide rails, gears, and cam systems. Without proper oil ("óleo") or grease maintenance, mechanical resistance will increase, causing the stepper motor to stall or skip steps. Mechanical Component Lubricant Type ("Óleo" / Grease) Maintenance Frequency ISO VG 32 to ISO VG 68 Machine Oil Every 40 to 80 operating hours Ball Screws / Lead Screws Lithium-based Grease (NLGI No. 2) Monthly or every 200 hours Feed Roller Gears High-tack Gear Oil or Synthetic Grease Every 100 operating hours Cam Mechanisms Heavy Industrial Oil (ISO VG 100) Step-by-Step Lubrication Procedure:
For the high‑current HB-B3HL variant (11A), consult the specific datasheet or use the factory‑default switch positions.
| Steps/Revolution | S0 | S1 | S2 | S3 | |------------------|-----|-----|-----|-----| | 400 | OFF | OFF | OFF | OFF | | 800 | ON | OFF | OFF | OFF | | 1600 | OFF | ON | OFF | OFF | | 3200 | ON | ON | OFF | OFF | | 12800 | ON | ON | ON | ON | Adjusted via switches S0–S3
The current setting on the DIP switches is too high, or the motor is stalling due to a lack of mechanical lubrication ("óleo") on the slide rails.
O óleo pode isolar os contatos dos bornes de pressão ou contaminar os optoacopladores de sinal, gerando perda de pulsos, o que faz a máquina cortar as sacolas no tamanho errado.
| Problem | Likely Cause | Solution | |---------|--------------|----------| | Driver overheats | Over‑current setting / poor ventilation | Reduce the phase current via DIP switches; improve airflow around the driver. | | Motor does not move | Wrong wiring / no control signal | Verify connections A→A, B→B, C→C. Check pulse and direction signals. | | Motor runs but lacks torque | Current set too low / supply voltage insufficient | Increase phase current (within motor limits) or check AC input voltage. | | Unusual noise or vibration | Step angle mismatch / resonance | Change step angle; add a small external resistor on the signal line (e.g., 1kΩ for 24V). | Entrada do trem de pulso que dita a
Caso o driver seja contaminado por óleo, desligue a energia completamente e limpe a placa eletrônica utilizando exclusivamente álcool isopropílico (puro 99.8%) ou limpa-contatos de secagem rápida. Nunca use solventes agressivos ou água. 4. Onde Baixar o Manual PDF?
8A, adequada para motores híbridos trifásicos de grande porte.
The machine didn't explode. It didn't even smoke. Instead, the HB-B3HL began to hum a low, melodic frequency. When Silas arrived the next morning, the bag-maker was running at triple speed. The stepper motors weren't just moving; they were
Se o seu motor de passo utiliza uma caixa de redução acoplada (comum para aumentar o torque em eixos tracionadores de plástico), verifique o manual do redutor. Redutores industriais necessitam de troca periódica de óleo lubrificante sintético conforme as horas de trabalho estipuladas. Resolução de Problemas Comuns (Troubleshooting)
seemed to be pulsing with a blue light that defied the workshop’s dim flickering bulbs. Silas rushed to the