Jmm-al10 Test Point

Refer to this YouTube demonstration to see the exact location, which is usually found near the connector labeled KCO-01 or JMM-AL10 . Test Point: The small gold dot. Ground (GND): Any metal shield part on the motherboard. Step-by-Step: How to Use JMM-AL10 Test Point (EDL Mode)

Have a question about the JMM-AL10 or other Huawei models? Drop a comment below or check out our Motherboard Repair Guides .

Shorting a power rail pad to ground can permanently fry the motherboard PMIC (Power Management IC). Ensure pinpoint accuracy with your tweezers.

Once you have exposed the motherboard and installed the necessary Qualcomm drivers on your computer, follow this sequence to connect the phone: jmm-al10 test point

Once the port is detected, you can release the tweezers. Open your chosen software, select the JMM-AL10 model, and proceed with the FRP reset or firmware flashing operation. Troubleshooting Common Issues

Locate the main logical board near the battery flex connection.

. This specific test point is a critical hardware bridge used by technicians to bypass software locks or unbrick devices that no longer boot normally. Technical Context & Purpose Refer to this YouTube demonstration to see the

I can guide you through the exact flashing steps for your situation. Share public link

Bypassing Google Account verification on Huawei Honor V9 Play/6C Pro. Bootloop Repair: Fixing phones stuck on the Huawei logo. 6. Troubleshooting If the phone is not detected:

The test point is a specific physical spot on the motherboard that, when shorted (connected) to ground, interrupts the normal boot process and forces the MTK processor into . This allows flashing tools to recognize the device even if it is dead or completely bricked. Chipset: MediaTek MT6750 Model: JMM-AL10 / Honor 6C Pro 2. Preparations Before Using the Test Point Step-by-Step: How to Use JMM-AL10 Test Point (EDL

to communicate with the MediaTek chipset before the system boots, enabling low-level flashing or partition erasing. Key Operations: FRP Bypass: Removing Google or Huawei account locks. Huawei ID Removal: Unlinking the device from a lost account. Dead Boot Repair: Reflashing the device when it does not power on normally. 2. Technical Specifications (JMM-AL10) Model Name Huawei Honor V9 Play / Honor 6C Pro MediaTek MT6750 Octa Core 4GB RAM + 32GB Storage (China Version) Android 7.0 (EMUI 5.x) 3. Procedure for Using Test Points

: Unscrew the bottom Pentalobe screws and carefully pry off the back cover.

While holding the short firmly, plug the micro-USB cable into the device.

Refer to this YouTube demonstration to see the exact location, which is usually found near the connector labeled KCO-01 or JMM-AL10 . Test Point: The small gold dot. Ground (GND): Any metal shield part on the motherboard. Step-by-Step: How to Use JMM-AL10 Test Point (EDL Mode)

Have a question about the JMM-AL10 or other Huawei models? Drop a comment below or check out our Motherboard Repair Guides .

Shorting a power rail pad to ground can permanently fry the motherboard PMIC (Power Management IC). Ensure pinpoint accuracy with your tweezers.

Once you have exposed the motherboard and installed the necessary Qualcomm drivers on your computer, follow this sequence to connect the phone:

Once the port is detected, you can release the tweezers. Open your chosen software, select the JMM-AL10 model, and proceed with the FRP reset or firmware flashing operation. Troubleshooting Common Issues

Locate the main logical board near the battery flex connection.

. This specific test point is a critical hardware bridge used by technicians to bypass software locks or unbrick devices that no longer boot normally. Technical Context & Purpose

I can guide you through the exact flashing steps for your situation. Share public link

Bypassing Google Account verification on Huawei Honor V9 Play/6C Pro. Bootloop Repair: Fixing phones stuck on the Huawei logo. 6. Troubleshooting If the phone is not detected:

The test point is a specific physical spot on the motherboard that, when shorted (connected) to ground, interrupts the normal boot process and forces the MTK processor into . This allows flashing tools to recognize the device even if it is dead or completely bricked. Chipset: MediaTek MT6750 Model: JMM-AL10 / Honor 6C Pro 2. Preparations Before Using the Test Point

to communicate with the MediaTek chipset before the system boots, enabling low-level flashing or partition erasing. Key Operations: FRP Bypass: Removing Google or Huawei account locks. Huawei ID Removal: Unlinking the device from a lost account. Dead Boot Repair: Reflashing the device when it does not power on normally. 2. Technical Specifications (JMM-AL10) Model Name Huawei Honor V9 Play / Honor 6C Pro MediaTek MT6750 Octa Core 4GB RAM + 32GB Storage (China Version) Android 7.0 (EMUI 5.x) 3. Procedure for Using Test Points

: Unscrew the bottom Pentalobe screws and carefully pry off the back cover.

While holding the short firmly, plug the micro-USB cable into the device.

SHARE WITH YOUR FRIENDS
Tung Sahur Clicker
Copy link
WHAT ISSUE DID YOU FIND IN
Tung Sahur Clicker